エラーコード0x6500112は様々な要因で発生するのですが、一つの原因としてターゲット（Destination）のLUNの属性が設定されていない（-replDest）ことが考えられます。以下がその設定の方法になります。

設定方法

uemcli -d ＜Unity IP アドレス＞ -u ＜ユーザ名＞ -p ＜パスワード＞ /stor/prov/luns/lun -id ＜LUNのID＞ set -replDest yes

属性の確認方法

uemcli -d ＜Unity IP アドレス＞ -u ＜ユーザ名＞ -p ＜パスワード＞ /stor/prov/luns/lun -id ＜LUNのID＞ show -detail

コマンド例　（LUNID：sv_400をターゲットLUNにしたいのでターゲットのフラグ（属性）を付与）

service@Unity300spa:~> uemcli -d XX.XX.XX.XX -u admin -p XXXX /stor/prov/luns/lun -id sv_400 set -replDest yes

Storage system address: XX.XX.XX.XX

Storage system port: 443

HTTPS connection

ID = sv_400

Operation completed successfully.

service@Unity300spa:~> uemcli -d XX.XX.XX.XX -u admin -p XXXX /stor/prov/luns/lun -id sv_400 show -detail

Storage system address: XX.XX.XX.XX

Storage system port: 443

HTTPS connection

1:    ID                         = sv_400

      Name                       = test2

      Description                =

      Group                      =

      Storage pool ID            = pool_6

      Storage pool               = test

      Type                       = Primary

      Base storage resource      = sv_400

      Source                     =

      Original parent            =

      Health state               = OK (5)

      Health details             = "The LUN is operating normally. No action is required."

      Size                       = 11811160064 (11.0G)

      Maximum size               = 281474976710656 (256.0T)

      Thin provisioning enabled  = yes

      Compression enabled        = no

      Compression space saved    = 0

      Compression percent        = 0%

      Compression ratio          = 1:1

      Current allocation         = 0

      Protection size used       = 0

      Non-base size used         = 0

      Family size used           = 2952790016 (2.7G)

      Snapshot count             = 0

      Family snapshot count      = 0

      Family thin clone count    = 0

      Protection schedule        =

      Protection schedule paused = no

      WWN                        = 60:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:CD

     Replication destination    = yes <=ここ確認

      Creation time              = 2017-12-13 08:14:07

      Last modified time         = 2017-12-13 08:25:56

      SP owner                   = SPA

      Trespassed                 = no

      FAST VP policy             = Start high then auto-tier

      FAST VP distribution       = Extreme Performance: 0%, Performance: 0%, Capacity: 100%

      LUN access hosts           =

      Snapshots access hosts     =

      IO limit                   =

      Effective maximum IOPS     = N/A

      Effective maximum KBPS     = N/A

上記の設定をした後に

uemcli -d -u <ユーザー> -p <パスワード> /prot/rep/session create -name -srcRes <ソースLUN ID> -dstType local -dstRes <ターゲットLUN>-syncType manual　

にてローカルリプリケーションを設定すればエラーになりません。

例

Unity300spa:~> uemcli -d xx.xx.xx.xx -u xxxx -p xxxx /prot/rep/session create -name Testayas -srcRes sv_401 -dstType local -dstRes sv_400 -syncType manual

Storage system address: xx.xx.xx.xx

Storage system port: 443

HTTPS connection

ID = 42949674120_APM00xxxx23096_0000_xxxx4117_APM00xxxxxxx_0000

Operation completed successfully.