This post is more than 5 years old
197 Posts
0
1802
November 18th, 2009 05:00
Responding via e-mail
I noticed we can now respond to a thread by replying to the e-mail that gets sent out, not sure if that was possible or not in the powerlink forums. My company puts a footer/disclaimer on our emails as they go out. Does anyone know if that would be put into the thread? I can imagine that would get a bit annoying.
No Events found!
aashishpatil
212 Posts
0
November 25th, 2009 16:00
Hi,
We've enabled the reply by email functionality. Check if it works for you now. You will need to reply to new notifications - replying to the old notifications will not work.
Try replying to this message by email to see if it works.
Thanks,
Aashish
RRR
2 Intern
•
5.7K Posts
0
November 18th, 2009 05:00
This proves that I harldy read more than half the each email
Test-test-test-1-2-3
Rainer_EMC
4 Operator
•
8.6K Posts
0
November 18th, 2009 05:00
unfortunately mine didnt.
what EMail adress did you send it to ?
Rainer
hersh1
197 Posts
0
November 18th, 2009 05:00
Mine didn't work either. Mine replys to this email emc-developer@sgaur.hosted.jivesoftware.com.
With a subject of this: RE: [Coffee Break] New message: "Responding via e-mail" [1a6qFy-m8k-1OuN]
Rainer_EMC
4 Operator
•
8.6K Posts
0
November 18th, 2009 05:00
does respond by mail actually work for you ?
when I try it the replies never make it to the forum
Rainer
RRR
2 Intern
•
5.7K Posts
0
November 18th, 2009 05:00
RRR
2 Intern
•
5.7K Posts
0
November 18th, 2009 06:00
emc-developer@sgaur.hosted.jivesoftware.com: this appears automatically when I press "Reply". Make sure you don't mess with the subject line.
Rainer_EMC
4 Operator
•
8.6K Posts
0
November 18th, 2009 06:00
yes, that's what I've been getting but still no go
I guess the fact that it doesnt work for me has to do with the EMC EMail setup since I'm replying from inside EMC
Rainer
Mabro1
2 Intern
•
666 Posts
0
November 18th, 2009 07:00
It does. That worked for me inside EMC. I replied directly to the post.
Regards,
Mark
CristianOrellan
107 Posts
0
November 18th, 2009 07:00
Hi,
Min doesn't work either, the reply always goes to:
emc-developer@sgaur.hosted.jivesoftware.com
I tried with two different subjects:
For the email body I use:
This is my test, I delete the whole content of the replied email and left only the end part.
--end--
Regards.
Mabro1
2 Intern
•
666 Posts
0
November 18th, 2009 07:00
Does this reply work?
Rainer_EMC
4 Operator
•
8.6K Posts
0
November 18th, 2009 07:00
doesnt work for me
Rainer
RRR
2 Intern
•
5.7K Posts
0
November 18th, 2009 08:00
hersh1
197 Posts
0
November 18th, 2009 09:00
aashishpatil
212 Posts
0
November 18th, 2009 09:00
This functionality is not functional - broken since migration. We are still trying to resolve this.
Thanks for your patience,
Aashish