Unsolved
This post is more than 5 years old
3 Posts
0
337605
August 4th, 2011 12:00
reset setting md 3000i
Hello
I have a problem with used md 3000i. I don't know its controllers static ip and MD3000 configuring wizard couldn't discover the storage.Does it exist a way to reset it to factory defaults using serial cable so I can access it via the management software?
best regards
Vitaliy
No Events found!
Dev Mgr
4 Operator
•
9.3K Posts
0
August 4th, 2011 12:00
You can use the serial cable to view and/or set the IP addresses for the management ports on the MD3000 series arrays. The serial cable is unique though (one side is a PS2/svideo type connector), so you'll have to have an MD3-series serial cable.
The steps to make the serial connection to set the IP addresses are the same as the steps to set up the serial connection to reset the password. This part is documented in the password reset pdf in the MD3000's online documentation:
Vitalkin
3 Posts
0
August 5th, 2011 02:00
I connected to MD3000i and scored command "ifShow".
result is below:
lo (unit number 0):
Flags: (0xc8049) UP LOOPBACK MULTICAST TRAILERS ARP RUNNING INET_UP INET6_UP
Type: SOFTWARE_LOOPBACK
inet: 127.0.0.1
Netmask 0xff000000 Subnetmask 0xff000000
inet6: ::1 prefixlen 128
Metric is 0
Maximum Transfer Unit size is 1536
0 packets received; 0 packets sent
0 multicast packets received
0 multicast packets sent
0 input errors; 0 output errors
0 collisions; 0 dropped
0 output queue drops
esmc (unit number 0):
Flags: (0x68843) UP BROADCAST MULTICAST ARP RUNNING INET_UP
Type: ETHERNET_CSMACD
inet: 10.217.1.110
Broadcast address: 255.255.255.254
Netmask 0xa000000 Subnetmask 0xad9016f
Ethernet address is 00:24:e8:72:28:e4
Metric is 0
Maximum Transfer Unit size is 1500
0 octets received
0 octets sent
47 unicast packets received
1 unicast packets sent
0 non-unicast packets received
0 non-unicast packets sent
I suspect, that controller's ip-address is 10.217.1.110 but i don't understand wich subnetmask i must use to connect to the controller via Ethernet cable
DELL-Steve R
62 Posts
0
August 5th, 2011 07:00
Hi, there is a guide in this link on how to reset a MD3000i using a serial cable, lists.us.dell.com/.../038389.html hopefully this should help, let us know if this work for you.
Steve
Vitalkin
3 Posts
0
August 6th, 2011 02:00
this guide didn't help me, when I scored "sysWipeZero 1" appeared error "C interp: unknown symbol name 'sysWipeZero'"
protocol from Hyper terminal is below
-=<###>=-
Attaching interface lo0... done
Adding 9767 symbols for standalone.
Error
08/06/11-07:44:54 (GMT) (tRootTask): NOTE: I2C transaction returned 0x0423fe00
BOOT OPERATIONS MENU
1) Perform Isolation Diagnostics 10) Serial Interface Mode Menu
2) Download Permanent File 11) Display Hardware Configuration
3) Reserved 12) Change Hardware Configuration Menu
4) Dump NVSRAM Group 13) Development Options Menu
5) Patch NVSRAM Group 14) Display Memory Error Log
6) Set Real Time Clock 15) Manufacturing Setup Menu
7) Display Board Configuration R) Restart Controller
8) Special Services Menu Q) Quit Menu
9) Display Exception Message
Enter Selection: 10
SERIAL INTERFACE MODE MENU
(Current mode is 'Console Only')
1) Console Only
2) Serial RAID Manager (SRM) Only
3) SRM or Console (assume SRM)
Q) Quit Menu
Enter Selection: 1
SERIAL INTERFACE MODE MENU
(Current mode is 'Console Only')
1) Console Only
2) Serial RAID Manager (SRM) Only
3) SRM or Console (assume SRM)
Q) Quit Menu
Enter Selection: Q
BOOT OPERATIONS MENU
1) Perform Isolation Diagnostics 10) Serial Interface Mode Menu
2) Download Permanent File 11) Display Hardware Configuration
3) Reserved 12) Change Hardware Configuration Menu
4) Dump NVSRAM Group 13) Development Options Menu
5) Patch NVSRAM Group 14) Display Memory Error Log
6) Set Real Time Clock 15) Manufacturing Setup Menu
7) Display Board Configuration R) Restart Controller
8) Special Services Menu Q) Quit Menu
9) Display Exception Message
Enter Selection: R
-=<###>=-
Attaching interface lo0... done
Adding 9767 symbols for standalone.
Error
08/06/11-07:45:23 (GMT) (tRootTask): NOTE: I2C transaction returned 0x0423fe00
Current date: 08/06/11 time: 00:35:03
LSI Logic RAID Controller
Copyright 2005-2009, LSI Logic Corporation. All Rights Reserved.
Copyright 1984-2006 Wind River Systems, Inc.
VxWorks: VxWorks 6.4 Kernel: WIND version 2.10
Model: 1532 Firmware version: 07.35.22.61
08/06/11-07:45:40 (GMT) (tRAID): NOTE: SOD Sequence is Normal, 0
08/06/11-07:45:40 (GMT) (tRAID): NOTE: SOD: removed SAS host from index 0
Serial Port shell started.
-> 08/06/11-07:45:40 (GMT) (tRAID): NOTE: In iscsiIOQLIscsiInitDq. iscsiIoFstrBase = 0x0
08/06/11-07:45:40 (GMT) (tRAID): NOTE: Turning on tray summary fault LED
08/06/11-07:45:42 (GMT) (tRAID): NOTE: SYMBOL: SYMbolAPI registered.
08/06/11-07:45:42 (GMT) (tRAID): NOTE: lost persistent dq data because buffer was modified or size changed.
08/06/11-07:45:46 (GMT) (tRAID): NOTE: Initiating Drive channel: ioc:0 bringup
08/06/11-07:45:48 (GMT) (tRAID): NOTE: IOC Firmware Version: 00-24-62-00
08/06/11-07:45:52 (GMT) (tNetCfgInit): NOTE: Network Ready
08/06/11-07:45:56 (GMT) (tSasEvtWkr): NOTE: sasIocPhyUp: chan:0 phy:0 prevNumActivePhys:2 numActivePhys:2
08/06/11-07:45:56 (GMT) (tSasEvtWkr): NOTE: sasIocPhyUp: chan:0 phy:1 prevNumActivePhys:2 numActivePhys:2
08/06/11-07:46:06 (GMT) (tRAID): NOTE: IonMgr: Drive Interface Enabled
08/06/11-07:46:06 (GMT) (tRAID): NOTE: SOD: Instantiation Phase Complete
08/06/11-07:46:06 (GMT) (tRAID): WARN: No attempt made to open Inter-Controller Communication Channels
08/06/11-07:46:06 (GMT) (tRAID): NOTE: LockMgr Role is Master
08/06/11-07:46:06 (GMT) (tRAID): WARN: FBM:validateSubModel: Exception - Alt controller not ready
08/06/11-07:46:06 (GMT) (tSasDiscCom): NOTE: SAS Discovery complete task spawned
08/06/11-07:46:07 (GMT) (tRAID): NOTE: spmEarlyData: No data available
08/06/11-07:46:07 (GMT) (sasCheckExpanderSet): NOTE: Expander Firmware Version: 0116-e05c
08/06/11-07:46:07 (GMT) (sasCheckExpanderSet): NOTE: Expander SAS address: Hi = x50024e84 Low = x7228e410
08/06/11-07:46:12 (GMT) (tSasDiscCom): WARN: SAS: Initial Discovery Complete Time: 30 seconds
08/06/11-07:46:12 (GMT) (tRAID): NOTE: WWN baseName 00020024-e87228e4 (valid==>SigMatch)
08/06/11-07:46:12 (GMT) (tRAID): NOTE: IonMgr: Host Interface Enabled
08/06/11-07:46:12 (GMT) (tRAID): NOTE: SOD: Pre-Initialization Phase Complete
08/06/11-07:46:13 (GMT) (tRAID): WARN: BID: initialize(): Power latched!
08/06/11-07:46:22 (GMT) (tRAID): NOTE: ACS: Icon ping to alternate failed: -2, resp: 0
08/06/11-07:46:22 (GMT) (tRAID): NOTE: ACS: autoCodeSync(): Process start. Comm Mode: 0, Status: 0
08/06/11-07:46:22 (GMT) (tRAID): WARN: ACS: autoCodeSync(): Skipped since alt not communicating.
08/06/11-07:46:22 (GMT) (tRAID): NOTE: SOD: Code Synchronization Initialization Phase Complete
08/06/11-07:46:23 (GMT) (tRAID): NOTE: Caught IconSendInfeasibleException Error in iop::requestAltIopDelay
08/06/11-07:46:23 (GMT) (tRAID): NOTE: CheckInMonitor: Check-in failed (IconSendInfeasibleException Error)
08/06/11-07:46:23 (GMT) (NvpsPersistentSyncM): NOTE: NVSRAM Persistent Storage updated successfully
08/06/11-07:46:23 (GMT) (tRAID): NOTE: USM Mgr initialization complete with 0 records.
08/06/11-07:46:23 (GMT) (tRAID): WARN: Received IconSendInfeasibleException Error adding small edr records from alt controller
08/06/11-07:46:24 (GMT) (tRAID): WARN: spm: unable to exchange features, assuming none
08/06/11-07:46:24 (GMT) (tRAID): NOTE: SPM acquireObjects exception: IconSendInfeasibleException Error
08/06/11-07:46:24 (GMT) (tRAID): NOTE: DBRead 0.103 secs
08/06/11-07:46:24 (GMT) (tRAID): NOTE: sas: Peering Disabled (Alt Unavailable)
08/06/11-07:46:25 (GMT) (tRAID): NOTE: QLStartFw: Downloading Driver's FW image 03.00.01.47 from 0317dea0 4c0c8 bytes , result 0
08/06/11-07:46:28 (GMT) (tRAID): NOTE: ********************************************************************************
08/06/11-07:46:28 (GMT) (tRAID): NOTE: QLogic Target Application, Version 2.01.08 6-13-2005 (W2K)
08/06/11-07:46:28 (GMT) (tRAID): NOTE: iSCSI Target Application
08/06/11-07:46:28 (GMT) (tRAID): NOTE: ********************************************************************************
08/06/11-07:46:28 (GMT) (tRAID): NOTE: QLInitializeFW: iSNS Server 0.0.0.0:3205
08/06/11-07:46:28 (GMT) (tRAID): NOTE: QLInitializeFW: ISNSServerIPv6Addr 00:00:00:00:00:00:00:00 :3205
08/06/11-07:46:28 (GMT) (tRAID): NOTE: QLInitializeFW: iSCSI Name iqn.1984-05.com.dell:powervault.md3000i.60024e80007228e4000000004a79b140
08/06/11-07:46:28 (GMT) (tRAID): NOTE: QLInitializeFW: port = 0, IPv4 Enable = 1, IPv6 Enable = 0
08/06/11-07:46:28 (GMT) (tRAID): NOTE: QLInitializeFW: IP Address 10.217.1.103:3260
08/06/11-07:46:28 (GMT) (tRAID): NOTE: QLInitializeFW: port = 1, IPv4 Enable = 1, IPv6 Enable = 0
08/06/11-07:46:28 (GMT) (tRAID): NOTE: QLInitializeFW: IP Address 10.217.1.104:3260
08/06/11-07:46:28 (GMT) (tRAID): NOTE: b_isn: Peering Disabled (Alt Unavailable)
08/06/11-07:46:28 (GMT) (tRAID): NOTE: ion: Peering Disabled (Alt Unavailable)
08/06/11-07:46:28 (GMT) (tRAID): NOTE: PM - reading DB (records 1..0)
08/06/11-07:46:28 (GMT) (tRAID): NOTE: CheckInMonitor: Check-in failed (IconSendInfeasibleException Error)
08/06/11-07:46:29 (GMT) (tRAID): NOTE: CCM: validateCacheMem() cache memory is invalid
08/06/11-07:46:29 (GMT) (tRAID): NOTE: CCM: validateCacheMem() Initializing my partition
08/06/11-07:46:30 (GMT) (tRAID): NOTE: CCM: initialize(): Configuring cache
08/06/11-07:46:31 (GMT) (tRAID): NOTE: Starting UWManager::initialize, entries 510, invalid index -1
08/06/11-07:46:31 (GMT) (tRAID): NOTE: Size of NVSRAM IW Queue is 0
08/06/11-07:46:32 (GMT) (tRAID): NOTE: RTR: IO Released
08/06/11-07:46:32 (GMT) (tRAID): NOTE: DiagVolManager::initialize: Exception - Alt controller not ready
08/06/11-07:46:32 (GMT) (tRAID): NOTE: Caught IconSendInfeasibleException Error in iop::requestAltIopDelay
08/06/11-07:46:32 (GMT) (tRAID): NOTE: SOD: Initialization Phase Complete
==============================================
Title: Disk Array Controller
Copyright 2005-2009 LSI Logic Corporation, All Rights Reserved.
Name: RC
Version: 07.35.22.61
Date: 03/12/2009
Time: 13:29:48 CDT
Models: 1532
Manager: devmgr.v1035api01.Manager
==============================================
08/06/11-07:46:32 (GMT) (tRAID): NOTE: sodMain Normal sequence finished, elapsed time = 52 seconds
08/06/11-07:46:32 (GMT) (tRAID): NOTE: sodMain complete
08/06/11-07:46:32 (GMT) (EventGateManager): NOTE: CheckInMonitor: Check-in failed (IconSendInfeasibleException Error)
08/06/11-07:46:33 (GMT) (ProcessHandlers): NOTE: SYMbol available
-> sysWipeZero 1
C interp: unknown symbol name 'sysWipeZero'.
nilush
2 Posts
0
September 23rd, 2016 04:00
Hi,
we just acquire a used MD3000i really cheaply. Unfortunately when I am trying to reset it with ctrl-B I am unable to make a selection. I type 10 hit enter and it just starts booting.
Did anyone else experience this issue?
tapelibraryfixer
2 Intern
•
427 Posts
0
September 23rd, 2016 06:00
i cant even get that far, i push ctrl-break on boot and it keeps booting until its finished
nilush
2 Posts
0
September 23rd, 2016 07:00
ctrl-break does work for me, but Remember you need to enter a capital S afterwards.
Lower case s doesn't work.
tapelibraryfixer
2 Intern
•
427 Posts
0
September 23rd, 2016 07:00
Hi
yeah i do all that nothing stops it booting though, and this is on multiple controllers, the menu appears but the boot-up text keep loading.