ax4-5f amber light in front

I have an ax4-5f that just came in.  When I boot it (i have the serial cable hooked up to verify), it appears to boot up fine but then goes into a state where the rear green light flashes 4x per second and drives 0-2 all have amber lights for them and the square status led in the front is amber.

The boot process stops with:

************************************************************
*                 Extended POST Messages
************************************************************

WARNING: BIOS: 05.14, ExpFw:   04.05, MC:    15.03, MCDL: 13.47
WARNING: POST: 05.34, ExpBoot: 03.00, CC/PS: 00.09
WARNING: LSI:  04.33, ExpIstr: 03.05, CPLD:  00.13
WARNING: SES Page Rev: 1:: 0=4, 1=4, 2=4, 3=4, 4=4
************************************************************

DDBS: K10_REBOOT_DATA: Count = 2
DDBS: K10_REBOOT_DATA: State = 0
DDBS: K10_REBOOT_DATA: ForceDegradedMode = 0

DDBS: SP A Normal Boot Partition
DDBS: MDDE (Rev 2) on disk 0
DDBS: MDDE (Rev 2) on disk 2

DDBS: MDB read from both disks.
DDBS: Chassis and disk WWN seeds match.
DDBS: First disk is valid for boot.
DDBS: Second disk is valid for boot.

FLARE image (0x00400007) located at sector LBA 0x000AE8C0

Disk Set: 0 2

Total Sectors: 0x00D6FAEE

Relative Sectors: 0x0000003F

Calculated mirror drive geometry:
Sectors: 63
Heads: 255
Cylinders: 877
Capacity: 14089005 sectors

Total Sectors: 0x00D6FAEE

Relative Sectors: 0x0000003F

Calculated mirror drive geometry:
Sectors: 63
Heads: 255
Cylinders: 877
Capacity: 14089005 sectors

EndTime: 04/24/2009 05:06:02

int13 - RESET (1)

int13 - READ PARAMETERS (3)

int13 - RESET (5)

int13 - READ PARAMETERS (7)

int13 - READ PARAMETERS (24)

int13 - READ PARAMETERS (547)

int13 - CHECK EXTENSIONS PRESENT (548)

int13 - GET DRIVE PARAMETERS (Extended) (549)

int13 - READ PARAMETERS (552)

int13 - CHECK EXTENSIONS PRESENT (553)

int13 - GET DRIVE PARAMETERS (Extended) (554)

int13 - READ PARAMETERS (556)

int13 - CHECK EXTENSIONS PRESENT (557)

int13 - GET DRIVE PARAMETERS (Extended) (558)

int13 - READ PARAMETERS (567)

int13 - CHECK EXTENSIONS PRESENT (568)

int13 - GET DRIVE PARAMETERS (Extended) (569)

int13 - DRIVE TYPE (586)

int13 - READ PARAMETERS (587)

int13 - DRIVE TYPE (588)

int13 - CHECK EXTENSIONS PRESENT (590)

int13 - GET DRIVE PARAMETERS (Extended) (591)

int13 - READ PARAMETERS (592)

int13 - CHECK EXTENSIONS PRESENT (593)

int13 - GET DRIVE PARAMETERS (Extended) (594)

int13 - READ PARAMETERS (605)

int13 - CHECK EXTENSIONS PRESENT (606)

int13 - GET DRIVE PARAMETERS (Extended) (607)

int13 - READ PARAMETERS (610)

int13 - CHECK EXTENSIONS PRESENT (611)

int13 - GET DRIVE PARAMETERS (Extended) (612)

int13 - READ PARAMETERS (1629)

int13 - CHECK EXTENSIONS PRESENT (1630)

int13 - GET DRIVE PARAMETERS (Extended) (1631)

int13 - READ PARAMETERS (1648)

int13 - CHECK EXTENSIONS PRESENT (1649)

int13 - GET DRIVE PARAMETERS (Extended) (1650)

int13 - READ PARAMETERS (1667)

int13 - CHECK EXTENSIONS PRESENT (1668)

int13 - GET DRIVE PARAMETERS (Extended) (1669)

int13 - READ PARAMETERS (1686)

int13 - CHECK EXTENSIONS PRESENT (1687)

int13 - GET DRIVE PARAMETERS (Extended) (1688)

int13 - READ PARAMETERS (1737)

int13 - CHECK EXTENSIONS PRESENT (1738)

int13 - GET DRIVE PARAMETERS (Extended) (1739)

int13 - READ PARAMETERS (1756)

int13 - CHECK EXTENSIONS PRESENT (1757)

int13 - GET DRIVE PARAMETERS (Extended) (1758)

int13 - READ PARAMETERS (1776)

int13 - CHECK EXTENSIONS PRESENT (1777)

int13 - GET DRIVE PARAMETERS (Extended) (1778)

int13 - READ PARAMETERS (1822)

int13 - CHECK EXTENSIONS PRESENT (1823)

int13 - GET DRIVE PARAMETERS (Extended) (1824)

int13 - READ PARAMETERS (1864)

int13 - CHECK EXTENSIONS PRESENT (1865)

int13 - GET DRIVE PARAMETERS (Extended) (1866)

 

 

Any ideas?  I was able to get to the utility partition and re-load FLARE but that does not seem to help at all