Unsolved
This post is more than 5 years old
265 Posts
0
1989
August 1st, 2012 14:00
spinfab
we have huawei dwdm fc200 2.125G fiber link connect two DataCenter , when we issue spinfab we got the below error , kindly advice
DCX-Lower-sw01:admin> spinfab -ports 2/19
Running spinfab ..............
ERROR: DIAG PORTSTOPPED spinfab:spinfab, 0 nMegs,
Pt2/19(66) Ch1/26 No Longer Transmitting, FTX Counter Stuck at 89583125,
Err# 13A012E 0242
spinfab: Completed 11 megs, status: FAILED.
port 83 test status: 0x00000002 -- FAILED.
FAILED.
DCX-Lower-sw01:admin>
kindly note link transfer rate is slow we got as max 16MB/s.
siwtches DS-4900B FOS v5.1.0a
DCX-4S FOS v6.4.2a
is there any parameter to change on brocade
----------------
fcping 10:00:00:05:1e:04:be:18
Destination: 10:00:00:05:1e:04:be:18
Pinging 10:00:00:05:1e:04:be:18 [0xfffc01] with 12 bytes of data:
received reply from 10:00:00:05:1e:04:be:18: 12 bytes time:1385 usec
received reply from 10:00:00:05:1e:04:be:18: 12 bytes time:1284 usec
received reply from 10:00:00:05:1e:04:be:18: 12 bytes time:1227 usec
received reply from 10:00:00:05:1e:04:be:18: 12 bytes time:1264 usec
received reply from 10:00:00:05:1e:04:be:18: 12 bytes time:1676 usec
5 frames sent, 5 frames received, 0 frames rejected, 0 frames timeout
Round-trip min/avg/max = 1227/1367/1676 usec
-------------------
DCX-Lower-sw01:admin> islshow
1: 17-> 23 10:00:00:05:33:5c:98:3a 43 HP_Enc1_sw1 sp: 8.000G bw: 8.000G
2: 72-> 0 10:00:00:05:33:5c:98:3a 43 HP_Enc1_sw1 sp: 8.000G bw: 8.000G
3: 83-> 44 10:00:00:05:1e:04:be:18 1 Fabric-A sp: 2.000G bw: 2.000G
--------------
portshow 2/19
portIndex: 83
portName:
portHealth: HEALTHY
Authentication: None
portDisableReason: None
portCFlags: 0x1
portFlags: 0x10004907 PRESENT ACTIVE E_PORT G_PORT LOGICAL_ONLINE LOGIN LED
LocalSwcFlags: 0x0
portType: 17.0
portState: 1 Online
Protocol: FC
portPhys: 6 In_Sync portScn: 16 E_Port
port generation number: 12098
state transition count: 22
portId: 1b5300
portIfId: 43220802
portWwn: 20:53:00:05:33:25:49:00
portWwn of device(s) connected:
Distance: normal
portSpeed: N2Gbps
LE domain: 0
FC Fastwrite: OFF
Interrupts: 0 Link_failure: 63 Frjt: 0
Unknown: 0 Loss_of_sync: 22 Fbsy: 0
Lli: 203 Loss_of_sig: 42
Proc_rqrd: 415367 Protocol_err: 0
Timed_out: 0 Invalid_word: 565795
Rx_flushed: 0 Invalid_crc: 0
Tx_unavail: 0 Delim_err: 0
Free_buffer: 0 Address_err: 2
Overrun: 0 Lr_in: 19
Suspended: 0 Lr_out: 13
Parity_err: 0 Ols_in: 3
Suspended: | 0 | Lr_out: | 13 |
Parity_err: | 0 | Ols_in: | 3 |
2_parity_err: | 0 | Ols_out: | 36 |
CMI_bus_err: | 0 |
Port part of other ADs: No
mdani1
56 Posts
0
August 7th, 2012 13:00
Output of the portshow and islshow clearly says that the link and sfp both are looking ok on this switch for this ISL port.
It can be due to huwai switch (dwdm) which brocade is not able to troubleshoot end to end link. You can try crossPort test , portloopback test to check further wether any issue on brocade end or not. If portloopback test is fine then you can open a case with your vendor to ask same but I dont think it matter to check spinfab for long ditance ISL's.